GLASS OUTER CYLINDERS
4 X 10 – Marvy No. 410
4 X 16 – Marvy No. 333, 405, 607
4 X 18 – Marvy No. 418
4 X 20 – Marvy No. 506
6 X 16 – Marvy No. 44, 56, 66 & Koken
6 X 17 – Koch & Paidar
6 X 20 – Marvy No. 77 & Koken
6 X 30 – Marvy No. 99 Koch & Paidar
8 X 19 – Koch & Paidar
8 X 20 – Marvy No. 88 & Koken
8 X 22 – Koch & Paidar
8 X 24 – Marvy No. 824 & Kokwn
REPLACEMENT LAMPS FOR BARBER POLES
15A15 – 130 V, Appliance Size, (15 watt)
FOR POLES WITH 4" DIAMETER GLASS
25T10/F – 130 V, (25 watt tubular type lamp, 5-1/4" length,
sometimes called a showcase lamp)
FOR POLES WITH 4" DIAMETER GLASS
40T10/F – 130 V, (40 watt tubular type lamp, 5-1/4" length,
sometimes called a showcase lamp)
FOR POLES WITH 6" DIAMETER GLASS
75A/RS – 130 V, (75 watt Commercial Service lamp)
FOR POLES WITH 8" DIAMETER GLASS
Please note: Above lamps are special long-life lamps,
good for approximately 2,500 hours.
18 Wat – Compact Fluorescent Screw-in Bulb
New-High efficiency, long-life (10,000 hours) - 1200 lumens
FOR POLES WITH 6" DIAMETER GLASS
MARVCYL® INNER CYLINDERS
All Marvcyls supplied with Metal Ends (spiders) attached –
except as noted.
3-1/4 X 10 – Marvy No. 410
3-1/4 X 16 – Marvy No. 405 & 607
3-1/4 X 18 – Marvy No. 418
3-1/4 X 20 – Marvy No. 506
3-1/2 X 16-1/2 – Marvy No. 333 - Available only without Metal Ends
4 X 14-1/2 – Paidar No. 928 - Available only without Metal Ends
*5 X 16-1/2 – Koch & Paidar - Must-re-use strap from old lower end
*5 X 17 – Koch & Paidar-“B” motor only
*5 X 29-1/2 – Marvy No. 99, Koch & Paidar
*5-1/4 X 16 – Marvy No. 55, 66 & Koken
– Marvy No. 44 - Order “full 5-1/4 X 16 without ends”
5-1/4 X 20 – Marvy No. 77 & Koken
*6-3/4 X 19 – Koch & Paidar - Fits Type “B” motor
unless Type “A” requested
*6-3/4 X 20 – Marvy No. 88 & Koken
*6-3/4 X 22 – Koch & Paidar - Fits Type “B” motor
unless Type “A” requested
*6-3/4 X 24 – Marvy No. 824 & Koken
*Above sizes prefixed with “*” are also available with “Hair Stylist” design, on request.
PAPER INNER CYLINDERS
(Preferred for restoration of old barber poles.)
All Paper Inner Cylinders with Metal Ends (spiders) attached – except as noted.
3-1/4 X 10 - Marvy No. 410
3-1/4 X 16 - Marvy No. 405 & 607
3-1/4 X 18 - Marvy No.418
3-1/4 X 20 - Marvy No. 506
4 X 14-1/2 - Paidar No. 928 - Available only without Metal Ends
5 X 16-1/2 - Koch & Paidar - Must re-use strap from old lower end
5 X 17 - Koch & Paidar "B" motor only
5-1/4 X 16 - Marvy No. 55, 66 & Koken
6-3/4 X 19 - Koch & Paidar - Fits Type "B" motor
unless Type "A" requested
6-3/4 X 20 - Marvy No. 88 & Koken
6-3/4 X 22 - Koch & Paidar - Fits Type "B" motor
unless Type "A" requested
6-3/4 X 24 - Marvy No. 824 & Koken
FLUORESCENT LIGHT SLEEVES:
Red, white & blue for use over fluorescent light tube
18" length
TOP CYLINDER BUSHINGS
LARGE SIZE TOP CYLINDER BUSHING BRIDGE - 5-3/4" long (plastic & metal). This bridge, which is a combination of plastic and sheet metal, is used on Marvy No. 88, 824 & Koken poles which use an inner cylinder of 6-3/4" diameter. (This bushing is not used on Paidar or Koch poles.)
STANDARD SIZE TOP CYLINDER BUSHING - 3-1/2" long (plastic). Fits Paidar & Koch barber poles; also fits Marvy No. 55, 66, 77 & 99 poles.
SMALL SIZE TOP CYLINDER BUSHING - 3" long (plastic).
Used on Marvy No. 405, 410, 418, 506 & 607 poles.
Will not fit Koken poles or Paidar & Koch poles.
ROUND TOP CYLINDER BUSHING - 2-3/4" diameter (plastic).
Fits Koken poles only. Standard replacement for Koken barber poles using a 6" diameter glass cylinder.
TOP CYLINDER SCREWS - (Two required).
Used on all poles where the top bushing is 3-1/2" or 3"
MOTOR MOUNTING PLATES
Type "A" fits Marvy poles with 6" or 8" diameter glass cylinders
Type "A-2" fits Marvy poles with 4" diameter glass cylinders
Type "C" fits most poles with 6" diam. glass cylinders,
EXCEPT KOKEN
Type "D" fits most poles with 8" diam. glass cylinders,
EXCEPT KOKEN
BARBER POLE MOTOR COIL - (Standard)
One style fits all barber poles - old style motors only.
42-TOOTH FIBRE GEAR - old style motors only
THREE WAY SWITCH - for barber poles
STAINLESS STEEL DOMES (tops) AND BOWLS (bottoms) FOR BARBER POLES DOMES (tops)
Marvy No. 333, 405, 410, 418, 506 & 607
(Inside Diameter of 5-1/4")
Marvy No. 44, 55, 66, 77 & 99
(Inside Diameter of 7-1/8")
Marvy No. 88 & 824
(Inside Diameter 9-1/2")
Paidar & Koch No. 98, 198, 99, 199, 102 & 202
(Inside Diameter of 9-1/2")
BOWLS (bottoms)
Marvy No. 333, 405, 410, 418, 506 & 607
(Inside Diameter of 5-1/4")
Marvy No. 44, 55, 66, 77 & 99
(Inside Diameter 7-1/8")
Marvy No. 88 & 824
(Inside Diameter of 9-1/2")
Paidar & Koch No. 98, 198, 99, 199, 102 & 202
(Inside Diameter of 9-1/2")
(Screws furnished with Domes and Bowls)
TWO LIGHT CONVERSION KITS
These conversion kits will convert Marvy barber poles, as indicated below, from a standard one-light barber pole to a two-light model. All parts needed for conversion will be included. Please specify model number for best results.
Kit to convert Marvy models 333, 405, 410, 418, 506, 607
Kit to convert Marvy models 55, 66, 77 & 99
Kit to convert Marvy models 88 & 824
SPECIAL ORDER LIGHT FIXTURES (Less Light Bulbs)
One-Light Model
Two-Light Model
Specify brand and model number of barber pole that you need the light fixture for. These are made to order.
PLASTIC GLOBES (unbreakable)
8" with 4" opening - fits Marvy 55, 66 & 77 Two-Light & Koken
10" with 4" opening - fits Koch & Paidar
GLASS GLOBES
(Milk White - For top of "Two Light" poles)
6" with 3" opening - fits Marvy 333, 405, 410, 418, 506, 607
8" with 4" opening - fits Marvy 55, 66, & 77 Two-Light & Koken
10" with 4" opening - fits Koch & Paidar
10" with 6" opening - fits Marvy 88 & 824 Two-Light & Koken
CANTEEN GLOBE 
12" with 4" Canteen Style" Glass Globe with decoration
Top
2/09
|
